To Top
En stock
SKU
ALT TS315

ALTO TS315 2000-WATT 15-INCH POWERED SPEAKER

2000 W peak (1300 LF + 700 HF) 1000 W continuous RMS (650 LF + 350 HF)
15-inch (381 mm) LF driver, 3-inch (76 mm) high-temperature voice coil
1.4-inch (35 mm) neodymium magnet HF driver with precision wave guide
Pole-mountable, wedge monitor, bracket installation or flown application with integral M10 suspension points

The new Alto Professional Truesonic TS3 Series does everything you demand in a no-compromise family of professional loudspeakers. These speakers solve every performance and installation challenge you have. They are high-performance in every sense: Their new transducers and amplifiers enable them to play extremely loud and clear, without compromise or restriction. And they are “high-performance” from a concept and manufacturing standpoint—we made sure that every aspect of their design outperformed what it had to do. The end result are loudspeakers that achieve a level of excellence and refinement that defies expectations. Defies your expectations. There are four models in the new TS3 range: The TS308, TS310, TS312 and TS315, with 8-10-12- and 15-inch woofers respectively. The range shares a new 2000-watt peak (1000-watt continuous) amplifier, a significant advance over the 1100-watt peak (550-watt continuous) amplifiers in the TS2. The four models boast all-new low-frequency drivers, designed to play louder and handle more power than their already-impressive predecessors, the wildly-successful TS2 Series. They also have a new horn-loaded high-frequency driver. This impressive transducer has a brand-new heat sink design that provides exceptional heat dissipation for impressive power-handling, even at all-night-long concert levels. Because these new drivers can safely handle the additional power, the TS3’s take full advantage of the increased wattage and will play at higher SPLs with lower distortion. We’ve even made the TS3’s easier to use, with an updated control panel and clearer control indications and detents that make for a faster, more precise setup. 2000 watts of bi-amplified power, newly-designed drivers and easier, more satisfying controls and setup—the new TS3 range doesn’t merely meet your requirements. It makes you re-think what’s possible. TECH INFORMATION Output Power: 2000 W peak (1300 LF + 700 HF) 1000 W continuous RMS (650 LF + 350 HF) LF Driver: 15-inch (381 mm) LF driver, 3-inch (76 mm) high-temperature voice coil HF Driver: 1.4-inch (35 mm) neodymium magnet HF driver with precision wave guide Crossover: 2 kHz Maximum SPL: 134 dB peak, 131 dB continuous (dB SPL @ 1 m) Frequency Response: 50 - 20 kHz (+/- 3 dB) Frequency Range: 43 Hz - 22 kHz (-10 dB) Horn Coverage: 90° H x 60° V nominal Equalization: Contour Switch Low and High Frequency +3dB Boost Connectors: (2) XLR/TRS 1/4” (6.35 mm) combo inputs, (1) XLR link output, (1) IEC power cable input Controls: (2) Volume, Power on/off switch, Contour switch, Ground-Lift switch Indicators: 2 x Power LED (front and rear), Clip limiter LED Protection: Electronic clip, Thermal and transducer overdrive protection Power Connection: IEC with Mains Fuse AC Voltage Input: 100,110-120,220–240 V, 50/60 Hz Enclosure: Trapezoidal, injection-molded, polypropylene enclosure, with perforated steel grille Mounting/Installation: 36 mm standard pole mount, Wall or ceiling mount using TSB125 bracket, Flown application with integral M10 suspension points, Wedge monitor Dimensions: (H x W x D): 25.7” x 16.6” x 15.4” / 652mm x 421mm x 392mm Net Weight: 41.3 lbs. / 18.8 kg. Design Origin: Designed and tuned in the USA Accessories: TSB125 Bracket, TS215 Cover

459,00 $
accordd_logoFinancing available for as low as 10,56 $ per month.
insta-icon SHOW YOUR GEAR #mdmd16494
Tag your public instagram photos or videos with #mdmd16494

The new Alto Professional Truesonic TS3 Series does everything you demand in a no-compromise family of professional loudspeakers. These speakers solve every performance and installation challenge you have. They are high-performance in every sense: Their new transducers and amplifiers enable them to play extremely loud and clear, without compromise or restriction. And they are “high-performance” from a concept and manufacturing standpoint—we made sure that every aspect of their design outperformed what it had to do. The end result are loudspeakers that achieve a level of excellence and refinement that defies expectations. Defies your expectations. There are four models in the new TS3 range: The TS308, TS310, TS312 and TS315, with 8-10-12- and 15-inch woofers respectively. The range shares a new 2000-watt peak (1000-watt continuous) amplifier, a significant advance over the 1100-watt peak (550-watt continuous) amplifiers in the TS2. The four models boast all-new low-frequency drivers, designed to play louder and handle more power than their already-impressive predecessors, the wildly-successful TS2 Series. They also have a new horn-loaded high-frequency driver. This impressive transducer has a brand-new heat sink design that provides exceptional heat dissipation for impressive power-handling, even at all-night-long concert levels. Because these new drivers can safely handle the additional power, the TS3’s take full advantage of the increased wattage and will play at higher SPLs with lower distortion. We’ve even made the TS3’s easier to use, with an updated control panel and clearer control indications and detents that make for a faster, more precise setup. 2000 watts of bi-amplified power, newly-designed drivers and easier, more satisfying controls and setup—the new TS3 range doesn’t merely meet your requirements. It makes you re-think what’s possible. TECH INFORMATION Output Power: 2000 W peak (1300 LF + 700 HF) 1000 W continuous RMS (650 LF + 350 HF) LF Driver: 15-inch (381 mm) LF driver, 3-inch (76 mm) high-temperature voice coil HF Driver: 1.4-inch (35 mm) neodymium magnet HF driver with precision wave guide Crossover: 2 kHz Maximum SPL: 134 dB peak, 131 dB continuous (dB SPL @ 1 m) Frequency Response: 50 - 20 kHz (+/- 3 dB) Frequency Range: 43 Hz - 22 kHz (-10 dB) Horn Coverage: 90° H x 60° V nominal Equalization: Contour Switch Low and High Frequency +3dB Boost Connectors: (2) XLR/TRS 1/4” (6.35 mm) combo inputs, (1) XLR link output, (1) IEC power cable input Controls: (2) Volume, Power on/off switch, Contour switch, Ground-Lift switch Indicators: 2 x Power LED (front and rear), Clip limiter LED Protection: Electronic clip, Thermal and transducer overdrive protection Power Connection: IEC with Mains Fuse AC Voltage Input: 100,110-120,220–240 V, 50/60 Hz Enclosure: Trapezoidal, injection-molded, polypropylene enclosure, with perforated steel grille Mounting/Installation: 36 mm standard pole mount, Wall or ceiling mount using TSB125 bracket, Flown application with integral M10 suspension points, Wedge monitor Dimensions: (H x W x D): 25.7” x 16.6” x 15.4” / 652mm x 421mm x 392mm Net Weight: 41.3 lbs. / 18.8 kg. Design Origin: Designed and tuned in the USA Accessories: TSB125 Bracket, TS215 Cover

Plus d’information
Fabricant
alto
bullet1
2000 W peak (1300 LF + 700 HF) 1000 W continuous RMS (650 LF + 350 HF)
bullet2
15-inch (381 mm) LF driver, 3-inch (76 mm) high-temperature voice coil
bullet3
1.4-inch (35 mm) neodymium magnet HF driver with precision wave guide
bullet4
Pole-mountable, wedge monitor, bracket installation or flown application with integral M10 suspension points
Rédigez votre propre commentaire
Vous commentez :ALTO TS315 2000-WATT 15-INCH POWERED SPEAKER
Votre évaluation

The new Alto Professional Truesonic TS3 Series does everything you demand in a no-compromise family of professional loudspeakers. These speakers solve every performance and installation challenge you have. They are high-performance in every sense: Their new transducers and amplifiers enable them to play extremely loud and clear, without compromise or restriction. And they are “high-performance” from a concept and manufacturing standpoint—we made sure that every aspect of their design outperformed what it had to do. The end result are loudspeakers that achieve a level of excellence and refinement that defies expectations. Defies your expectations. There are four models in the new TS3 range: The TS308, TS310, TS312 and TS315, with 8-10-12- and 15-inch woofers respectively. The range shares a new 2000-watt peak (1000-watt continuous) amplifier, a significant advance over the 1100-watt peak (550-watt continuous) amplifiers in the TS2. The four models boast all-new low-frequency drivers, designed to play louder and handle more power than their already-impressive predecessors, the wildly-successful TS2 Series. They also have a new horn-loaded high-frequency driver. This impressive transducer has a brand-new heat sink design that provides exceptional heat dissipation for impressive power-handling, even at all-night-long concert levels. Because these new drivers can safely handle the additional power, the TS3’s take full advantage of the increased wattage and will play at higher SPLs with lower distortion. We’ve even made the TS3’s easier to use, with an updated control panel and clearer control indications and detents that make for a faster, more precise setup. 2000 watts of bi-amplified power, newly-designed drivers and easier, more satisfying controls and setup—the new TS3 range doesn’t merely meet your requirements. It makes you re-think what’s possible. TECH INFORMATION Output Power: 2000 W peak (1300 LF + 700 HF) 1000 W continuous RMS (650 LF + 350 HF) LF Driver: 15-inch (381 mm) LF driver, 3-inch (76 mm) high-temperature voice coil HF Driver: 1.4-inch (35 mm) neodymium magnet HF driver with precision wave guide Crossover: 2 kHz Maximum SPL: 134 dB peak, 131 dB continuous (dB SPL @ 1 m) Frequency Response: 50 - 20 kHz (+/- 3 dB) Frequency Range: 43 Hz - 22 kHz (-10 dB) Horn Coverage: 90° H x 60° V nominal Equalization: Contour Switch Low and High Frequency +3dB Boost Connectors: (2) XLR/TRS 1/4” (6.35 mm) combo inputs, (1) XLR link output, (1) IEC power cable input Controls: (2) Volume, Power on/off switch, Contour switch, Ground-Lift switch Indicators: 2 x Power LED (front and rear), Clip limiter LED Protection: Electronic clip, Thermal and transducer overdrive protection Power Connection: IEC with Mains Fuse AC Voltage Input: 100,110-120,220–240 V, 50/60 Hz Enclosure: Trapezoidal, injection-molded, polypropylene enclosure, with perforated steel grille Mounting/Installation: 36 mm standard pole mount, Wall or ceiling mount using TSB125 bracket, Flown application with integral M10 suspension points, Wedge monitor Dimensions: (H x W x D): 25.7” x 16.6” x 15.4” / 652mm x 421mm x 392mm Net Weight: 41.3 lbs. / 18.8 kg. Design Origin: Designed and tuned in the USA Accessories: TSB125 Bracket, TS215 Cover